This article does not cite any references or sources. Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (May 2009)

Double metal studs designed to reduce noise transmission.

A wall stud is a vertical member in the light frame construction techniques called balloon framing and platform framing of a building's wall. It is variously also called "stick and platform", "stick and frame", or "stick and box" construction colloquially; the 'sticks' carry the vertical loads, and the rectangular platforms made of floor joists, headers and sub-floors, hold the outward forces in check and keep the walls in parallel and from bulging. In the mostly obsolescent and now rare balloon framing method, the wall studs are very long and tall and run from sill plate to roof plate, with the walls holding up the floors. In tall balloon framed buildings, studs are usually augmented by substantial posts, especially in the corners or mid-points of long walls.

The "sticks" refer to the wall studs and the wall plates which are much thinner in cross section than the structural elements in the older, Post and beam and Balloon framing methods of light frame construction. Being thinner and lighter, stick construction techniques are easier and speedier than the older methods, and balloon framing has been made illegal in new construction in many jurisdictions, for fire safety reasons—the plates and platforms in platform framing providing an automatic fire stop inside walls, and so are deemed much safer by fire safety officials.

Traditionally, studs were made of wood, usually 2×4 or 2×6 dimensional lumber. In North America, studs are typically placed 16 inches (400 mm) from each other's centre, but sometimes also at 12 inches (300 mm) or 24 inches (600 mm). Steel studs are gaining popularity, especially for non load-bearing walls.

Studs used to frame around window and door openings are given different names, including

• king stud − full length stud around the opening
• trimmer or jack − stud that supports the window or door header
• cripple − short stud above a header or below a window sill
• post or column - a doubled or other integral multiple of a group of studs nailed side by side, or (equivalent, a metal sheathed concrete filled column) used in a load bearing wall to transfer the weight of an upper structure to the bearing wall of a foundation, footing, and ground. Posts in walls are most common near high decorative windows, long spans near a wide window or sliding door, and so forth. Where architectural beauty conflicts with needs of engineering strength and safety.

Based on the WCLIB grading rules^[1], there is only one grade of stud: STUD. A stud is graded for vertical application, and it's stress requirements and allowable visual defects reflect that application. A Stud is most similar to a #2 grade, which is held to a higher standard during grading. The biggest difference between the two is the frequency, placement and size of knots and overall allowable wane.

[edit] Finding studs

This section contains instructions, advice, or how-to content. The purpose of Wikipedia is to present facts, not to train. Please help improve this article either by rewriting the how-to content or by moving it to Wikiversity or Wikibooks. (October 2009)

When mounting an object such as a shelf to a wall and maximum strength is desired, the goal is to attach the object to the studs in the wall, as mounting to drywall or plaster is only as secure as the material being mounted to.

Using a stud finder, one can find studs in most walls, though this may not work for very thick plaster, or plaster walls built with wire-lath.

If a stud finder does not work or is unavailable, it is often the easiest to tap lightly on the wall with the underside of one's fist. The resonating vibration especially from plaster and drywalls is an indication for a cavity behind. Tapping against a stud usually results in considerably less vibration. Another practice is to use a hammer and lightly tap on the wall while listening for sound differences until the stud is found. A third option is to resort to trial and error. Drilling a hole into the wall with a masonry bit, the difference between hitting a stud and not will be clear. If a stud is not hit, the bit will punch through quickly, with no resistance after the plaster or drywall. If a stud has been hit, the bit will put up considerable resistance. The bit may still drill into the wood or the metal, but progress will be slower. This difference is more manifest with a masonry bit than a wood drilling bit. After the first stud is found, others will typically be found 16 inches (about 40 cm) in either horizontal direction.

[edit] See also

• Framing (construction) which details each of
  • Balloon framing
  • Platform framing
• Post and lintel
• Post and Beam
• Walls
• Wall plates

1. ^ "WCLIB Grading Rules for National Grades - Framing Lumber"