Alconétar Bridge [A. 1]
Puente de Alconétar
Remains of the Alconétar Bridge with its flattened arches
Crosses	Tagus River
Locale	Garrovillas de Alconétar, Cáceres Province, Extremadura, Spain
Designer	Possibly Apollodorus of Damascus
Material	Stone
Total length	290 m (950 ft) [incl. approaches]
Width	6.55–6.80 m (21.5–22.3 ft)
Height	Minimum 12.50 m (41.0 ft)
Longest span	15 m (49 ft)
Number of spans	Ca. 18 [incl. flood outlets]
Completion date	Probably reign of Trajan or Hadrian (98–138 AD)
Collapsed	Yes
The remains were relocated in 1970 to a new site upstream. Alconétar Bridge

The Alconétar Bridge (Spanish: Puente de Alconétar), also known as Puente de Mantible, was a Roman segmental arch bridge over the river Tagus in the Extremadura region, Spain. The ancient structure, which featured flattened arches with a span-to-rise ratio of 4–5:1, is one of the earliest of its kind.^[1] Due to its design, it is assumed that the bridge was erected in the early 2nd century AD by the emperors Trajan or Hadrian, possibly under the guidance of Apollodorus of Damascus, the most famous architect of the time.^[2] The Alconétar Bridge belonged to the important Roman road Via de la Plata and should not be confused with the monumental Alcántara Bridge further downstream. It arguably remained in service until the Reconquista, numerous early modern reconstruction attempts failed. The ruins, which were mainly to be found on the right river bank, were relocated from its original position in 1970, when the Alcántara reservoir was created.

[edit] Location and road access

The relocated remains during a flood

The historic Alconétar Bridge spanned the Tagus not far from the mouth of the river Almonte, in the heart of the Spanish Cáceres Province in the Extremadura region.^[3] A modern motorway and a railway, which cross the Tagus in the immediate vicinity, underline the historical importance of this crossing point.^[3] During the building of the Alcántara Dam in 1970, the remains of the bridge were moved from their original site to a meadow six kilometers to the north, close to the municipality of Garrovillas de Alconétar.^[4] By contrast, few traces are left of the neighbouring ancient bridge over the river Almonte.^[5]

In the classical period, the Alconétar Bridge was part of the Roman road Iter ab Emerita Caesaraugustam, that was later called Via de la Plata. This important inner Iberian connection led from the provincial capital Mérida in the south, through the river valleys of Alagón, Tiétar and Tagus to the north, then on to the eastern part of Meseta Central, passing the major towns of Salamanca and Léon.^[6] Apart from the junction over the Tagus, the remains of four other ancient bridges can be found along the road: one over the Albarregas, another over the Aljucen, a third close to Caparra and a fourth over the Tormes.^[7] In the hills overlooking the Alconétar Bridge, a Roman mansio with the name of Turmulus (Spanish: "Ad Túrmulos") was established, according to the then customary distance intervals.^[5] It was the fourth of a total number of sixteen between Mérida und Astorga.^[8]

[edit] History

Remains, beginning with the 2nd floodway

The exact construction date of the Puente de Alconétar is unknown because of missing literary and epigraphic sources.^[9] Its extraordinary segmental arches suggest that it was built in the early second century AD, more specifically during the reign of the emperors Trajan (98–117 AD) or Hadrian (117–138 AD), as the use of this arch form was typical of that era. Both rulers were born in the southern Spanish province of Baetica and Trajan is known to have ordered the restoration of the Iter ab Emerita Caesaraugustam when he came to power.^[10] Segmental arches were often employed by Trajan's court architect Apollodorus of Damascus, such as in Trajan's Forum and most notably in the greatest civil engineering achievement of its time, Trajan's Bridge, which rested on twenty huge concrete piers and was used during the Dacian Wars for moving troops across the more than 1,000 m (3,300 ft) wide Danube.^[11]

2nd floodway. The arch thickness is 1.20 m.

Moorish geographers make no mention of the Alconétar Bridge, even though they praise the Roman bridge of Alcántara which also leads across the Tagus.^[12] There is some evidence that a community called Alconétar, Alconétara or Alcontra (Arabic: "small bridge") existed at least temporarily – probably an indirect reference to the high-rising bridge of Alcántara.^[5] It also remains unknown why the bridge of Alconétar is called Puente de Mantible in the local vernacular, an expression which alludes to the legend of Charlemagne and his Twelve Paladins.^[13]

The bridge was probably in use until the time of the Reconquista, when the Tagus constituted the border between the Christian and the Moorish realm from the 11th to the 13th century, and the frequent clashes might have easily made the ancient bridge unusable.^[14] According to another theory, the water could have begun to wash away the ancient foundations at the time.^[14]

The two arches 1 and 3, reconstructed in later times

The Alconétar Bridge first appears in records in 1231 and, again, in 1257, when it is explicitly referred to as being in use.^[15] It was probably repaired by the Knights Templar who had taken control of the bridge as well as the village in the meantime.^[15] The extant arches 1 and 3, both of which are not of Roman fabric, are assumed to date back to this period.^[15] Around 1340, however, the bridge was apparently unusable again, so that a ferry service was established to cross the river, which is also recorded at later times.^[15] On the site of the ancient way station, a fortress was erected in the Middle Ages; its tower built of Roman spolia overlooks the valley to this day.^[16]

Several attempts to reopen the bridge in the early modern era proved unsuccessful. In 1553, the architect Rodrigo Gil de Hontañón calculated a cost of 80,000 Ducats for the reconstruction of the bridge without ever realising his plans. The construction project of Alonso de Covarrubias and Hernán Ruiz of 1560 never went beyond the planning stage, and neither did another project between 1569 and 1580.^[6]

Long shot. In the foreground the two Roman flood openings 1 and 2

In the 18th century two further attempts to repair the bridge failed, in 1730 and 1760–70. The latter plan of the military engineer José García Galiano included a complete reconstruction with three large-span segmental arches. The planning sketch shows that already at that time the remaining arches were limited to the right bank, a finding confirmed by the drawing of Fernando Rodríguez from 1797 and the excellent engravings in Alexandre de Labordes' Voyage pittoresque de l'Espagne a few years later.^[6] The reconstruction sketch produced by Rodriguez (see diagram below) shows the profile of the bridge, rising evenly and dominated by three central arches in the centre of the river. These arches are flanked by a further nine segmental arches on both sides. The symmetry of the arches suggests that, in lieu of the fortification on the right bank viewed upstream, there might have been another segmental arch in Roman times.^[17]

The basis for the modern scientific analysis of the bridge was laid out by the civil engineer Antonio Prieto in his 1925 survey, which details the condition of the bridge before its relocation in 1970. Although this was a serious attempt to reconstruct the bridge as close to the original as possible, the Spanish scholar Durán points out that slight changes to the main body can never be avoided in the course of such a difficult undertaking.^[18]

The Puente de Alconétar is classified as "monument" by the Spanish authorities (as of 2009^[update]).^[19]

[edit] Construction

Ground plan of the extant bridge section

Arch no. 3. The right pier, no. 3, is the best preserved; the sloping support for the Roman segmental arch is easily recognisable.

Elevation of pier no. 3: The span-to-rise ratio of the ancient segmental arches can be calculated by using the degree of curvature of the originally preserved supports for the arch.

Main feature of the Alconétar Bridge was the segmental shape of its arches,^[20] which were rather uncommon in ancient bridge building. According to Prieto, the bridge had sixteen arches, not including the flood openings on the right approach, with the following spans (estimates are in square brackets):

• Meters: 7.30 – 8.20 – 9 – 10.15 – [11 – 12 – 13 – 14 – 15 – 14] – 13 – 12 – 11 – [10] – 9.30 – 9.10
• Feet: 24.0 – 26.9 – 30 – 33.3 – [36 – 39 – 43 – 46 – 49 – 46] – 43 – 39 – 36 – [33] – 30.5 – 29.9.^[9]

Other sources however vary from eleven to fifteen arches.^[21] The total length of the rectilinear structure was 290 m (950 ft), of which 190 m (620 ft) spanned the riverbed at low water.^[5] If one adds the clear span of the arches and assumes, on the basis of the preserved piers, an average pier thickness of 4.4 m (14 ft), then the distance between both bridge ramps was 244 m (800 ft) (= 178 + 15 x 4.4), which corresponded to a river cross section of 73%.^[4] By comparison, the corresponding discharge profiles for the Roman bridges of Córdoba, of Mérida and Salamanca were 62%, 64% and 80% respectively.^[22]

Most of the surviving fabric was concentrated on the right bank of the Tagus where the current was less strong; a number of pier stumps rose just above the water surface in the middle of the river, whilst on the left bank a further two piers remained standing, next to which the left abutment followed.^[23] The remains which were moved to a safe place before the flooding of the Alcantara reservoir in 1970 were essentially (see images): the right bridge ramp with its two arch-shaped flood openings, the piers 1, 2, and 3 with the remains of 4 and 6, as well as the vaults 1 and 3.^[4]

The approach to the ramp is 42 m (140 ft) long and 6.55–6.80 m (21.5–22.3 ft) wide.^[21] The clear spans of its two segmental arches are 6.95 m (22.8 ft) and 7.40 m (24.3 ft),^[21] which corresponds to a span-to-rise ratio of 4.0 and 3.3 to 1 respectively.^[24] The accurately fitting inclined contact surface of the springings clearly proves the Roman origin of these arches.^[25] With an extraordinary width of 1.20 m (3 ft 11 in), the voussoirs appear oversized in relation to the span (arch slenderness of 1:5.8 and 6.2 respectively).^[21] In contrast, the two surviving bridge arches no. 1 and 3 are instable substitutions, made of carelessly laid rubble.^[26] The date of these arches is unknown, as with all other repairs; possibly they were built in the period of the Knights Templar.^[15]

Equally evidently of post-classical origin is the masonry of the first two piers above the lower cornice, which projects from all piers at the same height.^[27] The superstructure of these piers could have been reconstructed for a drawbridge^[27] or a tower, which, according to an illustration in the Voyage Pittoresque, rested upon pier 2.^[16] In contrast, the third pier has still preserved its original Roman character up to the top at 12.50 m (41.0 ft). Its carefully worked ashlar and the second cornice, which ran along all ancient piers, provide us with the most distinct impression of the original shape of the Roman bridge.^[28]

In particular, it is possible to reconstruct relatively precisely the rise of the Roman segmental arches on the basis of the angles of the inclined stone supports at the springing level.^[16] Thus, the third arch originally described a circular sector of 95°,^[21] which points to a span-to-rise ratio of about 4–5 to 1 for the other segmental arches.^[16] This value is supported by de Labordes' engravings which depict an intact Roman segmental arch spanning the adjoining fourth bay as late as the early 19th century.^[27] Along with other early examples, such as Limyra Bridge and the Ponte San Lorenzo, the Alconétar Bridge therefore ranks among the oldest segmental arched bridges in the world. Its existence demonstrates that, in contrast to what had previously been widely believed and taught, Roman bridge builders possessed intimate knowledge of flattened arches.^[29]

The pier thicknesses, measuring 4.25 m (13.9 ft), 4.45 m (14.6 ft) and 4.55 m (14.9 ft), increase slightly towards the middle of the river, while the distances between the piers increase from 7.30 m (24.0 ft) to 10.20 m (33.5 ft).^[17] The fifth and ultimate pier, which carries the distinctive nickname "Bishop's table", takes an advanced position in the riverbed and possesses by far the largest cross-section (8.10 m (26.6 ft)). It may be of medieval origin and could have served as a base for a watchtower, replacing two ancient arches.^[30] All five piers are strengthened on the upstream face by pointed cutwaters.^[31]

The facing consists of granite ashlar; the interior of the piers was filled with Roman concrete, a common method applied for Roman bridges.^[32] Outwardly, the flattened arches must have lent the bridge a rather elongated appearance, with its roadway following a horizontal or slightly convex line.^[33]

[edit] Reconstruction and measurements

18th century elevation and ground plan by Fernando Rodríguez (view upstream). Above the bridge as of 1797, below his reconstruction attempt of the original Roman structure.

[edit] References

[edit] Annotations

1. ^ All measurements refer to the time prior to the bridge relocation and are necessarily fragmentary due to the ruined state of the structure.
2. ^ Estimated values in cursive
3. ^ All values refer to the relocated bridge.

[edit] Sources

• Durán Fuentes, Manuel (2004), La Construcción de Puentes Romanos en Hispania, Santiago de Compostela: Xunta de Galicia, pp. 181–87, ISBN 978-84-453-3937-4 
• Fernández Casado, Carlos (1970), Historia del Puente en Espania. Puentes Romanos: Puente de Alconétar, Madrid: Instituto Eduardo Torroja de la Construcción y del Cemento  without page numbers
• Galliazzo, Vittorio (1994), I ponti romani. Catalogo generale, Vol. 2, Treviso: Edizioni Canova, pp. 358–361 (No. 755), ISBN 88-85066-66-6 
• Gil Montes, Juan (2004), "Via Delapidata Elementos de la Ingeniería Romana", Las Obras Públicas Romanas, Tarragona: Congreso Europeo, http://www.traianvs.net/textos/delapidata.php Via Delapidata 
• González Limón, Teresa et al. (2001), "A Brief Analysis of the Roman Bridges of the Way "La via de la Plata"", in Lourenço, P. B.; Roca, P., Historical Constructions, Guimarães, pp. 247–256, http://www.csarmento.uminho.pt/docs/ncr/historical_constructions/page%20247-256%20_45_.pdf 
• O'Connor, Colin (1993), Roman Bridges, Cambridge University Press, pp. 108f. (SP20), 171, ISBN 0-521-39326-4 
• Prieto Vives, Antonio (May/Aug. 1925), "El Puente Romano de Alconétar", Archivo Español de Arte y Arqueología 2: 147–158 

[edit] See also

• List of Roman bridges
• Limyra Bridge

[edit] External links

• Media related to Alconétar Bridge at Wikimedia Commons
• Traianus – Technical investigation of Roman public works

v • d • e Roman bridges Germany Caesar's Rhine bridges  · Römerbrücke (Trier) France Pont Ambroix  · Pont de Bornègre  · Pont Flavien  · Pont du Gard  · Pont Julien  · Pont sur la Laye  · Pont des Marchands  · Pont Serme  · Roman Bridge (Saint-Thibéry)  · Roman Bridge (Vaison-la-Romaine) Italy Pons Aemilius  · Ponte Altinate  · Pons Cestius  · Pons Fabricius  · Pons Sublicius  · Pont d'Aël  · Pont de Pierre (Aosta)  · Pont-Saint-Martin  · Ponte d'Augusto (Rimini)  · Ponte Corvo  · Ponte del Gran Caso  · Ponte Milvio  · Ponte Molino (Padua)  · Ponte Nomentano  · Ponte Pietra (Verona)  · Ponte di Pioraco  · Ponte di Quintodecimo  · Ponte Salario  · Ponte San Lorenzo  · Ponte Sant'Angelo Portugal Ponte de Rubiães  · Ponte São João  · Roman Bridge (Chaves) Spain Acueducto de los Milagros  · Alcántara Bridge  · Alconétar Bridge  · Aqüeducte de les Ferreres · Puente Romano (Mérida)  · Segovia Aqueduct Bridge Syria Bridge at Nimreh  · Gemarrin Bridge  · Kharaba Bridge Turkey Aesepus Bridge  · Arapsu Bridge  · Bridge at Oinoanda  · Constantine's Bridge (Mysia)  · Eurymedon Bridge (Aspendos)  · Eurymedon Bridge (Selge)  · Karamagara Bridge  · Kemer Bridge  · Limyra Bridge  · Makestos Bridge  · Nysa Bridge  · Penkalas Bridge  · Pergamon Bridge  · Sangarius Bridge  · Severan Bridge  · Stone Bridge (Adana)  · Valens Aqueduct Bridge  · White Bridge (Mysia) Other countries Chesters Bridge  · Constantine's Bridge (Danube)  · Leontes Bridge  · Piercebridge Roman Bridge  · Trajan's Bridge Full list of Roman bridges

Coordinates: 39°45′14″N 6°26′14″W / 39.753838°N 6.437345°W / 39.753838; -6.437345

This article incorporates information from the revision as of 2009-12-12 of the equivalent article on the German Wikipedia.